Experimental video 1: seeks to show, that oil creates its own “virtual piping”, thereby establishing a direct path through the water, with minimal contamination of either oil or water. This experiment shows that water must be pumped out of the piping that goes to the surface to create the path/ but after that, the oil takes care of itself. It further indicates how quickly the oil and water do separate. (For Video, click here)/ a more detailed explanation below
Returning to the capture of oil by funneling the material beneath the sea: INTO a capture zone. What you have failed to functionally realize is: that oil and water being of different densities react hydraulically in very distinct ways. Oil being the lighter of the two, rising to the surface of its own accord. That means in very simple english: that the water becomes in effect a conduit for the oil to rise/ as it forces it way through the water to the place of least resistance; that it may rise to the surface. Creating that place of least resistance, for oil in water (the place where oil has already provided a path: it effectively creates “a pipe”, within the water itself; either aided by pumping/ or established with enough volume that it needs no pumping to rise to the surface. To create a capture zone the simple solution is to establish an upside down cone or funnel (small end upward), wherein the oil as it gushes upward from the simple physics of different specific gravities involved is contained. Simple physics demands: oil will rise almost vertically with little deviation, even though it expands it still remains within a defined area; thereby the capture zone, is sufficiently sized beyond that area of oil, at the height desired. If there is a current, you simply add a “sail”/ anchored to weights it simply directs the oil to where it then must go. This method can be used to collect underwater oil as well/ but understand if the oil does not rise/ then it is “a different oil/ from a different source”, and it is primarily a sludge, having lost its volatile mixtures. Nonetheless, if it is gathered together as a separate medium from the water/ it can be sucked up, by simply encountering the mass and giving it a place to go.
There are no issues of cold or freezing assigned by gas/ as these are not possible as you move the capture area in height above the outlet of oil. The ocean heat, in the water itself/ removes the cold. The only way ice forms a problem is if you have the wrong conditions set into place, by NOT providing the heat necessary to consume the cold/ or NOT containing the oil and gas sufficiently so that its escape effectively becomes as a refrigerant. The hydraulics of these materials does not change with depth or pressure. What is a less dense material (oil) will rise, when contained by a higher dense material (water). As to significant gas, the reality is “a bigger capture zone is required”/ but apart from that it is merely an inconvenience, in terms of collecting oil. Oil direct from the well head, is not diluted/ nor separated even in the presence of gas, because gas needs the same path of least resistance as does the oil.
It is a clear, and unmistakable reality: that those in charge of the oil spill today/ meaning largely the US government officials, including the president: WANT primarily TO CAPTURE and contain the oil for sale, FAR MORE than they wish to protect the environment. Having removed the piping from the top of the blowout preventer, there is literally nothing stopping them from lowering a cone shaped plug into that well head and stopping the flow of oil. They have a drilling rig directly above/ they lowered a collecting cap and pipe directly onto the oil gushing out: which means they have all the tools necessary to replace that cap with a cone shaped plug/ and insert it into the gaping hole and shove it down into place with the weight of the piping and drilling ship from the surface. Attaching it there can be done in a number of ways. Included in this reality is the pipe not cleanly cut can be modified with reamers, held on the end of the drilling pipe and turned by the surface drilling team, as well as lathe ends put on that same pipe to completely smooth the impacting surface. Held in place simply by inserting the appropriate sized pipe. Critical care can exist to insure the cutting heads are not damaged on impact by the use of hydraulics to control the cutting edge force or position. It is possible to create a seal along with this insertion pipe/ along the same lines as an annular seal, but with teeth at the top to get a grip on the pipe being inserted too/ so that tension, to pull out, is minimal. [I strongly suggest you simply plug it instead; because enough damage has been done]. The drilling pipe section that does the work, can also be the means of anchoring the plug in place by simply preparing it for that purpose first. Once attached to the well, a long arm attached to that section becomes the wrench for unscrewing this section by means of a submersible, OR an in place propulsion unit which will turn the section above by using water force/ after a hydraulic ram gives the initial push to dislocate the bottom section from the next higher. Or you can just make a slip section with a collar that simply lets go when you tell it to. Either way, it is the government in charge at this point whether they say so or not, particularly the president and the coast guard making a decision to capture rather than plug the hole. A pipe originally when through this blowout preventer/ a pipe currently exists at the top/ therefore we know it is possible to put a plug in this hole. We hear from “all the leaders, new media allows”/ that they are more concerned with oil and jobs, than the long term effects of complete environmental devastation. That includes most of the public whose main concern is GET ME THAT OIL. That means, it is no longer strictly a BP/ etc problem, but exists because of fundamental society demands: making it a price all society must pay. The obvious tax, goes to oil and all oil products: YOU WANTED IT CHEAP/ now pay, this is what you chose. Because when only money matters, nothing else does, therefore risk is multiplied until catastrophe occurs; until life itself is being lost/ only then does this society learn to care about anything but Gluttony and consumption. Some say “2.7 trillion miles a year” are driven/ want to explain how that is not excess? Not to worry though, like the historical figure who wanted gold so much he killed everyone not made into a slave: he got to drink that gold, as a fitting reward. The president says: “he’s furious, cause these people gambled with other lives, etc”. Yet he has allowed: being in charge of the military/ the experimentation of creating fusion at NIF, a facility, in a suburb of San Francisco; which can bring the same fire as is on the sun here to this earth. Fusion being the burning of atomic bonds/ here, in a place where everything is then fuel. It will be, “like throwing a match in gasoline/ with no possibility of putting it out”. [they want free energy/ they want no pollution: so they risk every life on earth; gambling. Because you want free energy and no pollution too; free everything. Failure is death of a planet, and you will fail, because the burning of atomic bonds cannot be stopped]! Or genetic mutilation, wherein everything called nature is being crucified! [because they want to be gods/ they want to erase death, or any of the maladies, and VERY MANY want to construct living creatures by their own design]. But they are not gods! The tragedy unfolding as complete chaos, irrevocable: because NATURE IS, the genetic structure which builds our bodies and minds and everything else, in time. Genetic structure is “a billion instructions, governing the construction of every living thing; in a size so very small, this cannot be found without a microscope”. Genetic operations, are granted and delivered with a conceived “one part per billion” chemical released instruction format which then determines IF you will have arms or legs or a head, or a mind, etc. And men play with this, as if their actions were not “satan himself”.] . These want to play god, and they are playing with every life, every future, everything we are. The obvious outcome will be like the oil spill/ but with absolute chaos for all life; forever/ all dead. As with oil spilling, it only takes one eruption: to cause tremendous damage. Apart from oil, genetic mutilation is not possible to recover from, not for anyone, or anything, on this earth. Shame on you for such arrogance, such total disregard for life/ for pride which knows no boundary beyond making something or someone else your slave. SHAME ON YOU, THAT YOU ARE SO ASLEEP/ DULL/ AND DIM-WITTED, YOU PERCEIVE NONE OF THIS “the experts” have made you fools: wake up or die/ it is that simple. Like your money, which has been filled with lies/ the university has become the biggest liar of all: “they want to be gods/ and believe they are (because you let them believe it, and the media propagate this lie, for power & pride; regardless of truth: SELL IT)”. As with all the games of men, even if you can win; there is nothing to be gained, because the passion of this world being led by men is: WE WANT MONEY FIRST/ and little else matters. Shame on you. I know you have to make money to live/ or more correctly must work to live and trade. But like the biblical story of adam and eve: if you take the very last fruit, without thinking of the future (NEED THAT SEED): “that part of life, will disappear from you”. The absolute failure of men is: “I/we can make you fight”/ that is the game! Life is not a game, and you will change or die. Oil is not “wonderful”/ if it takes away your life; and that decision is now being made. life and death (in this instance of risk and reality) is a choice, dependent upon truth. The current reality of leadership by men is LIAR/ THIEF/ WHORE/ & FAILURE. Because you choose money first/ you demand a game, instead of respecting life/ you destroy the future, and say HOW VERY PROUD we are; “we are gods”! Shame on you as well, if you read this and do not do what you can to establish a change in this oil disaster/ regardless of what you think about me. This crisis can multiply; do it now.
With hope, that the containment cap being tried today has some success/ it is realistic to add: that additional oil can be collected with the simple addition of an upside down funnel to the collecting pipe once the cap is installed. The oil will want to follow the pipe anyway/ therefore a smaller upside down funnel will work; just a few feet above the cap itself, perhaps twenty to assure no problems with freezing can occur. Regardless of the exact height, without dispersants: the oil will vertically rise in its own column. Thereby all that is necessary is a cone shaped sheet of metal or fabric or plastic that is cut to overlap on one side so that the funnel is layered essentially, with the appropriate sized hole in the center. That cut will allow you to simply put it around the collecting pipe. And then slide it down that collecting pipe to the proper distance above. Once at height, a series of cable loops “like lacing a shoe” will draw the funnel together and tighten the center hole to attain a relative seal. Added to this is the addition of an additional riser pipe, by simple means at the side of the center hole; for collecting the oil lost to the main collection pipe, and sending it to the surface. There is absolutely no cause to burn off the gas/ it rises with the pipe contained; and can easily be separated and stored. Dispersants are the chemicals that cause volatile (lighter/ gaseous) components to separate out from the oil. That means in this process, they create sludge/ and sludge is slow to rise, causing “plumes”. As to the collection of sludge on the surface; the fan/tray wheel described below is the most efficient method. Set on top of a barge, with two or more paddle style wheels on each side/ these can simply dip out the oil/ and dump it into the ocean going barge: as would a grain elevator leg dumping corn. There is no need for “the little water valves” as are indicated in the alternate version below or at a different link in oil spill (this site)/ because propulsion by the pumping of water, can simply use the excess coming in. The use of a grain leg style conveyor is expected to work/ but it will push the oil away somewhat because the buckets are not in contact with the oil and water long enough, this represents a quick vertical rise/ and a scooping action as in the wheel will be more effective. The alternative is an alteration to the bottom of a “grain style leg”/ wherein the bottom is stretched to create an incline that is suitable for collecting oil on the surface/ giving the risers a v- shape instead of a parallel rise together. Where the oil is extensive, there is no need for human beings on board the barge. Simply attach a long cable and pull it through the oil. A cable pull allows for immediate usage of current barges/ as opposed to adding propulsion outriggers. Even so a suitable propulsion method for a barge moving slowly through the water is sucking water and oil into the barge from the forward means of travel/ and sucking water out from the bottom of the oil/ water contained in the vessel to push the barge using jets of water for propulsion and directional control. If an access road is available pull it to the shore where the barge can be unloaded by truck/ if not: then drop an anchor and pull it into the ocean, where a ship will then unload or a separate barge can pump and move the oil to land. Make sure they actually do something with the oil collected/ the only reasonable thing would be to pump it back into an abandoned oil well/ for later collection: equipment already there.
Any extensive sea or surface movements/ any expressive currents created by storms below the surface; can cause this current cap to “fall off”. Suitable methods of anchoring that collection pipe must be found, as it is going to remain in position, and be necessary; a significant amount of time.
The use of oil well suction pumps/ attached to a slowly moving barge, can also simply suck up the majority of oil, and will work effectively, so long as you suck the water that is collected out from underneath this oil. They are however expected to be “less efficient/ and more energy intensive to operate”.
The use of “people in play suits”, is functionally illiterate when confronting millions of gallons of oil. The assumption that “oil must go on as is”/ just because a few thousand people more will be unemployed, is absolutely insane. JUST BECAUSE YOU WANT something/ does not mean it is to be tolerated, accepted, or allowed. Critical failure HAS occurred, and until that situation is completely resolved, and the foundations for a much more secure future for ALL: has been established. Everybody suffers the same. This is not only BP failure/ it is US government failure/ state failure/ industry failure/ public failure/ and even environmentalist failure (YOU were not prepared either: yelling is NOT enough). But even so, when none will listen, because they are LITERALLY CONSUMED BY THEIR OWN WANTS; nothing will get done, except the demand: MAKE ME RICH/ and as we all know making someone rich MEANS, “the creation of very many people that will be excessively poor”. Money, is a human thing; it has nothing to do, beyond what human beings demand of it: people demand slaves/ thereby money exists.
In terms of alternate methods of collecting oil: the foundation is, that you must not disturb the oil on top or gathered together any more than is possible to do. Turbulence creates “froth; the intermixing of water and oil” which gives it a consistency much harder to deal with/ until it separates itself, which it does by separating into various chemical components. Consequently two simple things are important: collect quickly to avoid weather if possible/ don’t stir. But remember you cannot truly skim oil off of water effectively/ BUT YOU CAN such the water out from underneath the oil on top. Leaving you with a product that is relatively pure/ and water taken out, that is consistent with the best we can do. Another method of doing that is: to lower a large flat “sheet” below the water with pontoons. Push it under a major amount of oil and fill the pontoons with air to collect or contain the oil and water into a confined area. With a suction line fitted to the sheet you pump out the water, when this line becomes filled with oil/ you move the transfer line from ocean to tanker.
a cap that does not seal, collects water do to the suction capabilities of capillary action, due to turbulence (unless you create a volume of oil that stays in place around this opening, by inverted funnel to refuse the water. The original concrete dome did not work, because the piping was full of water, and that allowed the cold to be entrapped. It was also built of the entirely wrong material, as heat transfer is essential. Should have looked like an accordion “lots of surface area”.) water in the presence of cold can freeze. The apparent mixing chamber located at a height above the well cap, for introducing methanol to stop the freezing will require very significant amounts of ethanol/ but the freezing could easily occur below it. What is useful, is to understand there need not be a wait period for getting the oil to the surface/ simply pump the water out. While it is correct, that the weight of the water pushes the oil up, because of density differences/ it is also true the weight of water within the piping causes an unnecessary delay. A pump should be employed/ because the pressures within the well pipe are such that they overcome the volume requirements of that pipe/ therefore a pump is needed to increase the flow up the pipe/ and keep less oil from escaping/ a sufficient flow keeps the gas in tow. Careful valving reduces the introduction of water/ but controlling the oil, leaves the gas with a need to expand at the cap; thereby increasing freezing. Even so pressures and heat from the oil/ and the water as it rises to the surface, should keep this piping open. Therefore simply let the ice rise until it melts/ instead of methanol. Even here, at the bottom end of the collection pipe, just above the cap; IF you can keep the pipe running/ then you can also establish an upside down funnel at this lower level, on the pipe to collect what is missed. The correct uptake of oil, will leave a small amount of oil within the funnel itself/ to keep the water out, if gas escapes, more oil is needed. The inverted funnel needs “heat transfer fins, or the equivalent”. Without this buffer zone, it is impossible to keep the water out/ the current cap will not keep the water out, unless it is completely engulfed by roughly 40% oil loss, and even then gas bubbles will allow water in. Once in place and working, the piping can still be lifted to reintroduce the oil into the collection pipe (if necessary) if you can pump fast enough to keep up. Otherwise it needs a separate collection pipe to the surface.
The functional requirements of sending down the necessary funnel to collect the oil have been discussed in www.justtalking3.info with other designs for use in collecting the oil already in the water and beaches. It has been there since one week after the oil began/ it became apparent as always: fools were in charge.
I will add more: in the use of a “umbrella stem” that provides support off the bottom of the sea for this funnel system or the alternate “tent/ teepee” arrangement of supporting the necessary structure. The functional arrangement of the umbrella support allows for a “diamond style opening at the top of the umbrella/ funnel for the oil to find its way into the pipe that extends from there to the surface. The funnel is built like an umbrella with similar supports to maintain its position. The new addition is if you wish to try cutting the pipe from the blowout preventer: then this funnel needs to be in place first [in case you get even more oil coming out]. Regardless with the cap built onto the lower stem that holds the funnel in place. It is entirely possible to work underneath the funnel/ while capturing the oil. That means no greater ill effects should occur even if the leak increases. And if you get it done properly/ then create a lowering effect in the diamond zone/ to allow a hydraulic cylinder to let the funnel be lowered closing the hole and connecting the two pipes [above the funnel, and below the funnel as a support stem, together], by turning them together. Even so, not done; because until you lock these structures to the floor of the sea by weights to hold it all in place during a storm or latch the structures to the blowout preventer so that this anchors the piping during a storm. Or arrange the necessary cabling as in high rise antenna towers here on land to the sea floor, a storm will still be a problem. Consequently preparations must be in place; either with anchor locations placed or prepared.
The construction of simple arms welded onto the structural stem that work like a vice grip plier; by surrounding the blowout preventer/ in effect hugging it, is simple enough: “think of handcuffs”. The use of any functional mechanical or hydraulic means to clamp these arms around the blowout preventer needs no further detail.
As to the cap on the end of the stem in preparation for attachment to the blowout preventer, it NEEDS the following design: instead of arms that go around the blowout preventer. This cap must be prepared with, a claw like hook arrangement as is common to a “wheel, or pulley, puller” [found throughout the mechanical industry]. This wheel puller WILL have a circular band around the claws so that as you let the claws engage the band falls, thereby holding the claws in place. Each claw can be activated mechanically with worm drives AND the entire claw or puller arrangement SHALL have a secondary attachment: which will draw the cap down onto the blowout preventer/ by pulling against the claw/ puller: already fully attached to the blowout preventer/ while pulling against the pipe. Use of the schematics of the blowout preventer itself, will indicate exactly what type of claw is needed. A suitable sealing ring at the bottom of this cap where it joins to the blowout preventer is necessary: such as is the use of chemicals that will close the gap= A series of independent rubber rings, with gaps containing a suitable release mechanism for the chemicals to mix/ once pressure is applied from seating against the blowout preventer. Suit yourself, what kind. The alternate method is: instead of a cap, a cone shaped pipe is lowered into the blowout preventer itself. IF there is no collar to be unbolted/ THEN there is a pipe inside the blowout preventer which can be mated too/ by simply inserting another pipe of a smaller diameter, prepared with a taper. Piping DID go through this blowout preventer to drill the hole! That leaves an area outside the piping, where the annular seal is leaking. To stop this a donut/ washer shaped collar is fitted above the tapered pipe, with “O-ring” seals inside. This collar, with seals as above; is then able to slide up and down the new piping, and if mated properly will go down onto the top of the blowout preventer. Therefore the collar is several feet tall/ so that tapers and areas around the piping as needed can be ignored. The collar itself is to be anchored in place by a cable system that goes around the outer ring of the collar through pulleys which then give the cable a saw tooth appearance when connected to the blowout preventer by the use of “handcuff style clamps” OR whatever works best. An electric winch is then used to tighten the collar to the blowout preventer/ or a suitable tool on the sub, will simply tighten the cable with a mechanical means. CAUTION is to be recognized in this method of dealing with the leak/ because flow rate is primarily dependent upon the size of the pipe. IF THAT PIPE is currently crushed to half its diameter, prior to spilling oil/ THEN cutting that pipe will increase the flow 50%. NOT twenty percent! Without the proper structural arrangements, no possibility for keeping this cap exists in a storm. Severe leaking as is possible/ will then bring the demand to remove the blowout preventer itself, so that a pipe can be installed within a pipe: and that will be worse, removing the base possibilities for structurally maintaining a seal or hold on the well itself.
video experiment number 2: seeks to show, the immediate separation of oil and water, when surface allows. Thereby creating the consequence of two separate environments which can then be exploited for the collection of oil. Machines which exploit this reality are identified in the various links in this category called OIL SPILL, on this site.
Another device for picking up heavy oils on the surface in calm water is as follows: pushed before the vessel so as not to disturb the mixture with a propellor/ or pulled in a larger version by two vessels, with this machine in-between the vessels. The reality is: THE OIL IS, on top. Thereby a skimming platform is all that is essential for a large portion of heavy contamination. A skimming platform is nothing more than one submersible float or pontoon, parallel to the motion of the vessel/ or crossways in front of the vessel pushing it; that moves into the water causing the water/ oil mixture to rise as in a wave until it washes over the pontoon rise: what is on top, the oil; is then on the other side of this float and can be collected as primarily oil by simply making a tub from which to collect it (this differs from an alternate method already described only slightly, in real terms: just an alternate description for understanding; one of several machines in the different links aligned with “oil spill” on this site). Therefore all that is needed is a front float, which can be flooded with water so as to submerge to correctly adjust the height desired; in relation to speed and depth of oil being collected. And then a pan or bowl behind that float for the transfer of oil to the barge being towed behind it as the tank required for oil storage. And a vessel to tow it creating the necessary force. It will work better to have one collector on each side of the vessel, to keep the wake of the propeller from causing problems/ or just push it.
Another method is the revolving drum, built like a squirrel cage fan/ only with trays instead of blades. This model sits on floats above the sea surface which can be submerged like a submarine by flooding the compartments to attain the correct height above the sea surface. Once set into place the “fan-like collector” simply scoops up the top surface of heavy oil residue, by turning the drum. Inside the fan collector is a half moon gutter, with seal on the back edge (to wipe the oil on the inside surface of the turning drum) so that the oil collected in the scoops will fall into the gutter and be removed by the pump through the axle piping; into a waiting/ or tow behind tank. The scoops will contain small holes for draining water, that are closed by a simple flap valve: made of an appropriate material that floats in water, but loses buoyancy in oil. As the drum goes over center, the oil is then dumped into the gutter inside.
This particular type of machine can be set alongside the beach. Incorporated with an auger that runs down the gutter from one end to the other/ and is used to clean sand. The sand is augured in/ the scoops collect ocean water to run over the sand as it passes along through/ out it comes on the other end, [different auger or means of conveyance returns it to shore]; relatively clean: where the oil and water is collected/ allowed to separate, or forced to.
These are not hard machines to conceptualize; therefore no picture is necessary. If you cannot do so/ then ask, and a rough drawing will be done. There are area’s that will be separated as oil begins to deteriorate into its component parts: these essentially have to be seined/ fine screen moved slowly to collect the particulate matter as best you can. It can be vacuumed and centrifuged, but that takes considerable energy. The use of dispersants are a terrible choice, [they make it impossible for sea life to breathe/ and contaminating MUCH larger areas of the sea floor, and its life or ability to return!] multiplying the tragedy by ten, “out of sight”, is NOT “better”.
Experiment 3 is an alternate view of the upside funnel down with smaller equipment. The first video is with 134a refrigerant being released, its capture can be seen with the funnel if the piping is sized to the gas being released. Second part is strictly oil release, with capture of that oil, contained if the surface pipe or pumping is sufficient. Third part is with oil and gas together, and same is true. To accomplish all oil and gas instead of water combined with it; you MUST have, a layer of oil contained by the funnel, so that what is taken upward is then replaced without allowing water to come inside to any great extent. With oil and gas combined; more water will be necessary, because gas opens the oil for water to enter/ as it expands and contracts. All three substances are pumped into a tanker/ and the water will settle to the bottom, where the majority of water is removed with a simple pump there.
As to this reality in truth and dimension of life: it is just a tiny introduction to the horror and catastrophe that is coming due to genetic mutilation by men. A tiny discovery in this oil is: you cannot depend upon the university/ they cannot fix very many things. Thereby pointing to the blatant and irrevokable end of life for an entire planet, that is the creation of fusion here on earth: FUSION IS, the burning of atomic bonds/ and therefore, NOTHING here on earth is not fuel! We all burn, if fusion begins; there are many more threats. Genetic DNA IS NATURE! That reality means men are mutilating it without concern/ deliberately trying to play god/ trying to make “insect men, etc”/ crucifying it/ deliberately trying to wreck and destroy the genetic disciplines and balance that give us all, every life on earth: “both body and mind”. Wake up or die/ there is no going back!
Functionally as serious, over time: is the fact that trillions of gallons of freshwater from aquifers are being pumped into oil and natural gas under the earth to make it rise. Trillions of gallons lost in the production of gasohol. Trillions of gallons lost to pollution in various forms. The aquifers are failing/ which means the people and life which depend upon them will have no water to drink. Contrary to what people think, a single rain does not replenish an aquifer/ RATHER IT TAKES 50 INCHES OF RAIN, TO EQUAL ONE INCH OF WATER RETURNED TO AN AQUIFER. In addition to that if you recognize how many gallons of fuel are burned, in this nation or world and multiply by no less than 5 times that amount in volume equals the oxygen content of air as is needed to produce that fire: you get an amount of air roughly 250 feet above your head that the oxygen within it is taken just for fire: YOU do not get a breathe/ until the oxygen above lowers; the fire takes it all. As to global warming, there is no debate, simply add it up: the amount of fuel burned times the btu’s released into the atmosphere= global warming by man.
This is just the beginning, just the end of millions of tons of seafood; because kill one single link in the chain of life/ and everything above that point will die. A reality describing the introduction of insanity and despair as is coming onto this earth; because fantasy and delusion, have ruled/ lies, deceit, and money first will die/ or you will. Truth is coming, because nothing lives without truth, and a world destroyed or unbalanced as is the result of what men do today: is everywhere. It’s a choice, to believe we must not gamble/ we must choose life first; that, is the truth. IT’S A CHOICE, to investigate, examine the evidence, establish wisdom as best you can: and then let truth decide for itself, what it is we as human beings must do. It’s a choice, to believe overpopulation can be sustained: currently an increase of 2 million more mouths to feed/ over deaths, each and every week. BUT, It’s a choice, that will end in cannibalism; think for yourself.
To the local tv station: I have built a simple experiment to show the visual realities of oil collection. Which simply means, I can show you and your camera, that although oil is introduced into clean water, it can and is collected with minimal contamination of either oil or water. Proving the funnel effect stated above. A demonstration of another type of machine for separating oil is also available for viewing. I do demand a copy of your digital recording if you come to view it/ that I may use it on my own site, listed above. There is no other charge, all inventions and information is free. Just use it. I expect to be working at____________(one block away); on the guttering June 1, between one and two o’clock; with the experiments in hand. If you wish to view them. James Osterbur. The invited chose not to show/ the rest were known not to be willing.
Of some interest is the wording used by the coast guard “in charge”: having some trouble, but cap will soon get most of the product into the ships above [a summary]. Or more simply, the major concern is not about environment: THEY WANT the oil. Therein the “government response” is exactly the same as the oil companies, and their companion industries. TO HELL with life/ GIVE US THE DAMN MONEY.